Aluminum Circle For Spinning
Aluminum circle for spinning
Our high quality spinning aluminium circle are mainly used for : Lighting, Ventilation, Satellite, Paint Sprayers, Cenral Vacuum Units, Filter Cartridges, Planters, Waste Recepticles
| Chemical composition | ||||||||
| Alloy (%) | AA 1050 | AA 1070 | AA 1200 | AA 3003 | AA 3103 | AA 8011 | AA 5251 | AA 6082 |
| Fe | 0.4 | 0.25 | 1 | 0.7 | 0.7 | 0.6 1.0 | 0.5 | 0.5 |
| Si | 0.25 | 0.2 | (Fr + Si) | 0.6 | 0.5 | 0.5 0.9 | 0.4 | 0.70 1.30 |
| Mg | 0.05 | 0.03 | – | – | 0.3 | 0.05 | 1.70 2.40 | 0.60 1.20 |
| Mn | 0.05 | 0.03 | 0.05 | 1.00 1.50 | 0.90 1.50 | 0.2 | 0.10 0.50 | 0.40 1.00 |
| Cu | 0.05 | 0.04 | 0.05 | 0.05 0.20 | 0.1 | 0.1 | 0.2 | 0.2 |
| Zn | 0.05 | 0.04 | 0.1 | 0.1 | 0.2 | 0.2 | 0.2 | 0.2 |
| Ti | 0.03 | 0.03 | 0.05 | 0.10 (Ti + Zr) | 0.10 (Ti + Zr) | 0.08 | 0.2 | 0.1 |
| Cr | – | – | – | – | 0.1 | 0.05 | 0.2 | 0.25 |
| Each (others) | 0.03 | 0.03 | 0.05 | 0.05 | 0.05 | 0.05 | 0.1 | 0.05 |
| Total (Others) | – | – | 0.125 | 0.15 | 0.15 | 0.15 | 0.2 | 0.15 |
| Al | 99.5 | 99.7 | 99 | Remainder | Remainder | Remainder | Remainder | Remainder |
Automatic circle blanking production line processing
The main components of the aluminum disk uncoiling and blanking production line are: loading trolley, uncoiling machine, leveling machine, feeder, swing unit, special closed single-point mechanical press, quick die changing device, palletizing unit, scrap shear Cutting, hydraulic system, electrical control system, etc.
Technical characteristics of production line:
1. Fully numerically controlled, the production line should start from the unwinding of the coil, until the entire roll of material is blanked, no manual contact with any materials is needed, no adjustments are needed, and the potential safety hazards of ordinary punches are basically eliminated Hidden product quality.
2. The line can directly use the coil to produce circles without the need for slitting and cross-cutting of the coil, which reduces the production process, reduces the cost of production, and reduces the possibility of damaging the surface of the coil. The disc is guaranteed to be free of oil and scratches.
3. This line makes full use of the width of the coil and uses high-precision servo motor drive system control to minimize the circle spacing and the distance from the circle to the material edge, radically reduce the amount of waste, and make the raw material utilization rate reach 80% the above.
4. Production speed can reach 40-55 tablets per minute, which improves production efficiency.
5. Due to the use of a modular mold design, when converting circle production specifications, the conversion time can be reduced to less than 15 minutes. The diameter of circles that can be produced ranges from 85 mm to 750 mm.
6. Advanced unwinding system, six-level leveling machine, high rigid mechanical press, automatic palletizing system, etc., ensure the high quality of circle products.